Skylight Flashing and Re-Roofing in Calgary: What to Check

Learn how skylight flashing fails on Calgary roofs, what proper flashing looks like, and why it should be replaced during a roof replacement, not reused.

Skylights let in a lot of light, but the hole they create in a roof deck is also one of the most demanding details on the entire structure. The flashing around a skylight has to shed water, resist wind uplift, and survive repeated freeze-thaw cycles every winter without failing at a single seam. On most Calgary homes we inspect, a skylight leak traces back to the flashing or the sealant around it, not to the skylight unit itself.

That distinction matters because it changes the scope of the fix. A failed bead of sealant is a small job. Corroded step flashing or a crushed head flashing after a hailstorm is a bigger one, and it often surfaces only when a full roof replacement is already being planned. This guide covers what skylight flashing is supposed to do, what to look for from inside the house, and how skylight flashing in Calgary projects typically gets handled during a re-roof.

None of this applies only to skylights installed decades ago. Even a skylight added five or six years ago can develop a flashing problem if the original installation skipped a step, or if a later roof repair disturbed the flashing without resealing it correctly.

Why Skylights Are a Common Leak Point on Calgary Roofs

A skylight curb interrupts the plane of the roof, which means water has to be redirected around it instead of just running downhill. Every seam in that redirection, where the flashing meets the asphalt shingles or metal roofing, where panels overlap, where sealant bridges a gap, is a potential failure point. Calgary's climate puts extra stress on all of it.

  • Freeze-thaw swings common to Alberta climate cause metal flashing and the materials around it to expand and contract repeatedly, which loosens fasteners and opens hairline gaps in sealant over a few seasons.
  • Snow that melts during a chinook and refreezes overnight can build an ice dam right at the base of the skylight curb, backing water up under the flashing instead of letting it drain away.
  • Spring hailstorms can dent or crack a skylight dome and bend the metal flashing around it, creating a direct path for water even if the glazing itself is not punctured.

This is why skylight flashing in Calgary needs more frequent attention than it would in a milder climate: the freeze-thaw cycle alone puts more stress on the seals than most other parts of the roof see in a year. Sealant is the part most homeowners notice failing first, because it is visible from a ladder. But sealant is meant to be a secondary defense, not the main one. When a roofing contractor relies on caulking alone to keep a skylight dry, rather than built-up step and head flashing, the repair tends to fail again within a year or two.

What Good Skylight Flashing Looks Like

Proper skylight flashing is a layered system, not a single piece of metal. Each component has a specific job, and they are installed in a sequence that lets water drain down and out rather than pooling against the curb.

  • Step flashing runs up the sides of the skylight curb, with individual pieces woven in under each course of asphalt shingles so water is directed outward at every layer.
  • Head flashing sits at the top, or uphill, side of the curb and carries water around the high point, usually extending further up the roof deck than homeowners expect.
  • Saddle or apron flashing covers the lower edge, directing water that has come down the sides and over the head flashing out past the bottom of the curb instead of back under it.

How this ties into the roof surface depends on the system. On an asphalt shingle roof, the flashing integrates course by course with the asphalt shingles themselves and the underlayment beneath them. On a metal roofing installation, the flashing has to match the panel profile and is usually sealed with butyl tape or a compatible sealant rather than woven in the way it is under asphalt shingles. Raico installs skylight flashing as part of both asphalt roofing and metal roofing projects, since the flashing method differs between the two. Either way, the underlayment under and around the curb matters as much as the visible metal - it is the backup layer if the flashing ever develops a pinhole leak. The same logic applies to flashing around windows and doors on exterior walls, which is why a window and door flashing problem often shows the same staining pattern as a skylight leak. Flashing installed with careless workmanship is a common root cause of a skylight leak, not a defect in the skylight unit itself.

A common mistake on older re-roofs is reusing the existing skylight flashing to save a day of labor. Flashing that has been through ten or more Calgary winters has usually lost enough flexibility that it will crack again within a season or two, often at a fastener hole that was never visible from the ground.

Skylight Flashing During a Full Roof Replacement

When a roof replacement is already underway, the skylight flashing should come out with the old asphalt shingles or metal roofing, not stay in place underneath the new material. New flashing costs little relative to the overall project, and reusing old flashing defeats the point of doing a full roof replacement at all - the weakest part of the old roof gets left behind under a new surface.

The table below gives a general sense of how an isolated flashing repair compares to flashing work done as part of a full re-roof. These are typical ranges for planning purposes, not a quote - actual scope depends on the number of skylights, roof pitch, and what the roofing contractor finds once the old material is off.

ScopeTypical TimelineWhat's Involved
Isolated flashing repairPart of a dayReplace flashing and sealant around one skylight
Flashing replacement in a re-roofRoughly half a day added per skylightNew step, head and saddle flashing tied into new underlayment
Flashing plus skylight replacementA full day or more per unitRemove and reset the curb, usually after storm damage

A homeowner in a Killarney bungalow with a single kitchen skylight will see a very different scope than a commercial property manager in an industrial park with a dozen roof-mounted units feeding a warehouse floor below. Raico Roofing scopes skylight flashing separately on every roof repair or re-roof quote for exactly that reason.

Signs to Check From the Attic or Ceiling

Most skylight flashing failures show up indoors before they show up during a roof inspection from outside. A quarterly look through the attic or at the ceiling around a skylight catches problems while they are still a repair, not a rebuild.

  • Brown or yellow staining on the drywall or ceiling finish around the skylight opening, even if it is faint and only shows up after a storm.
  • A thin line of daylight visible around the skylight shaft when standing in a darkened attic during the day, which points to a gap in the flashing or curb seal rather than normal light transmission through the unit.
  • Condensation trails or a damp line running down the inside of the skylight shaft in cold weather, which can mean warm, moist indoor air is reaching cold flashing and condensing rather than a true water leak.

That last point matters because condensation and an actual flashing leak can look similar at first glance but need different fixes. Poor attic airflow around a skylight shaft often ties back to the same ventilation balance that affects the rest of the roof, which is covered in more detail in our piece on attic ventilation balance. A roofing contractor who only looks at the flashing from outside can miss a ventilation problem entirely.

Timing and Cost Framing for Skylight Flashing Work

An isolated skylight flashing leak, caught early, is a modest roof repair: a few hours of labor to remove the affected section of asphalt shingles or metal roofing, replace the flashing and sealant, and tie it back into the surrounding material. Waiting until staining spreads across the ceiling turns that into a drywall repair on top of the roofing work, which adds cost without changing the underlying scope of the flashing fix.

Skylight flashing in Calgary re-roofing projects is best planned for in spring or summer, when temperatures allow sealants and adhesives to cure properly and when a multi-day project is less likely to be interrupted by snow. A roof replacement scheduled in late fall can still include proper skylight flashing work, but the window for ideal curing conditions is narrower, and a roofing contractor with Alberta climate experience will usually flag that at the quoting stage rather than after the tear-off has started.

Property managers overseeing commercial roofing with multiple roof-mounted skylights should budget for flashing replacement as a line item on any re-roof, not an afterthought discovered mid-project. The same applies to a homeowner planning a broader exterior renovation that includes new asphalt shingles or metal roofing, aluminum gutters, and fascia and soffit work. Skylight flashing belongs on that same scope sheet from the start, since the roofing contractor already has the old material off and the curb exposed.

Skylight flashing failures are rarely dramatic until they are ignored for a season or two. Catching the staining, the daylight gap, or the condensation trail early keeps the repair small. If a skylight on your roof is showing any of these signs, or you want flashing handled properly during an upcoming roof replacement, contact Raico Roofing to have it inspected.

Frequently Asked Questions

Can a skylight flashing leak be fixed without replacing the skylight itself?

In most cases yes. If the skylight dome and frame are intact and the leak traces to the flashing or sealant around the curb, a roofing contractor can remove the surrounding roofing material, replace the flashing, and reseal without touching the skylight unit. Replacement of the skylight itself is usually only needed if the frame has cracked, warped, or sustained direct storm damage.

How often should skylight flashing be checked on a Calgary home?

A visual check from inside the attic once a season, especially after a spring hailstorm or a stretch of chinook freeze-thaw weather, catches most problems early. From the roof surface, flashing is worth a closer look any time the surrounding asphalt shingles or metal roofing are already being inspected, such as after a storm or during routine maintenance.

Does home insurance typically cover skylight flashing failure?

Coverage usually depends on the cause. Sudden storm damage, such as hail cracking a dome or wind tearing flashing loose, is more commonly covered than gradual deterioration from age or wear, which most policies treat as a maintenance issue rather than an insurable event. A homeowner should review their specific policy with their insurer rather than assume either outcome.

Can skylight flashing be installed on a flat or low-slope commercial roof the same way as a sloped residential roof?

No. On a flat or low-slope commercial roof, skylight flashing has to rely more heavily on curb height and membrane detailing rather than the shingle-course weave used on a sloped residential roof, since there is little pitch to help shed water away from the opening on its own.

More articles

All articles

Contact Raico Roofing for a free quote.